CCNA 2 v6.0

CCNA 2 v6.0 Final Exam Answers Option A 100%

CCNA 2  v6.0 Final Exam Answers Routing and Switching Essentials (Option A) 1. Refer to the exhibit. Which highlighted value represents a specific destination network in the routing table? 0.0.0.0 172.16.100.64* 172.16.100.2 110 791 2. Refer to the exhibit. Assuming that the routing tables are up to date and no ARP messages are needed, after a packet leaves H1, how many times is the L2 header rewritten in the path to H2? 1 2* 3 4 5 6   3. Which type of static route is configured with a greater administrative distance to provide a backup route to a route learned from a dynamic routing protocol? standard static route floating static route* default static route summary static route 4. Refer to the exhibit. Which route…Read More...

CCNA 2 v6.0 Final Exam Answers Option B 100%

CCNA 2 v6.0 Final Exam Answers Routing and Switching Essentials (Option B) 1 Refer to the exhibit. Host A has sent a packet to host B. What will be the source MAC and IP addresses on the packet when it arrives at host B? Source MAC: 00E0.FE91.7799 Source IP: 192.168.1.1 Source MAC: 00E0.FE10.17A3 Source IP: 10.1.1.10 Source MAC: 00E0.FE91.7799 Source IP: 10.1.1.10* Source MAC: 00E0.FE10.17A3 Source IP: 192.168.1.1 Source MAC: 00E0.FE91.7799 Source IP: 10.1.1.1 2 What is the effect of configuring the ipv6 unicast-routing command on a router? to assign the router to the all-nodes multicast group to enable the router as an IPv6 router* to permit only unicast packets on the router to prevent the router from joining the all-routers multicast group 3 What is a characteristic of a static route that creates a gateway of last resort? It backs up a route already discovered by a dynamic routing protocol. It uses a single network address to send multiple static routes to one destination

CCNA 2 v6.0 Final Exam Answers Option C 100%

CCNA 2 v6.0 Final Exam Answers Routing and Switching Essentials (Option C) 1 Refer to the exhibit. Assuming that the routing tables are up to date and no ARP messages are needed, after a packet leaves H1, how many times is the L2 header rewritten in the path to H3? 1 2* 3 4 5 6 2 Refer to the exhibit. Which highlighted value represents a specific destination network in the routing table? 0.0.0.0 172.16.100.128* 172.16.100.2 110 791 3 On which two routers would a default static route be configured? (Choose two.) stub router connection to the rest of the corporate or campus network* any router where a backup route to dynamic routing is needed for reliability edge router connection to the ISP * any router running an IOS prior to 12.0 the router that serves as the gateway of last resort 4 Which command will create a static route on R2 in order to reach PC B? R2(config)# ip route 172.16.2.1 255.255.255.0 172.16.3.1 R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.2.254

CCNA 2 v6.0 RSE Chapter 2 SIC Practice Skills Assessment Option A – Packet Tracer Answers | CCNA5.NET

CCNA 2 v6.0 Routing and Switching Essentials Chapter 2 SIC: Static Routing and Basic Router Configuration Type A Chapter 2 SIC Practice Skills Assessment A few things to keep in mind while completing this activity: Do not use the browser Backbutton or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessmentbutton in the browser window to submit your work. Introduction New Corp. is preparing to convert its network to use IPv6. It is experimenting with the transition, and has set up a test network that is configured with both IPv4 and IPv6 addressing on all hosts and device interfaces. The company will be using default, static, and floating static routes to create connectivity in the network. In this practice skills assessment, you will configure the New Corp. network with IPv4 and IPv6 interface and host addressing, and IPv4 and IPv6 default, static, and floating static

CCNA 2 v6.0 RSE Chapter 2 SIC Practice Skills Assessment Option B – Packet Tracer Answers | CCNA5.NET

  • 29/03/2018 18:29
  • /
  • 84

CCNA 2 v6.0 Routing and Switching Essentials Chapter 2 SIC: Static Routing and Basic Router Configuration Type B A few things to keep in mind while completing this activity:1. Do not use the browser Back button or close or reload any exam windows during the exam.2. Do not close Packet Tracer when you are done. It will close automatically.3. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure SW-1 with an initial configuration, SSH, and port security. You are only required to configure SW-1 in this assessment. All IOS device configurations should be completed from a direct terminal connection to the device console. It is possible that information that is required to complete the configurations has not been given to you. In that case, create the values that you need to complete the requirements. These values may include certain IP addresses, passwords, interface descriptions,

CCNA 2 v6.0 Chapter 7 RSE Practice Skills Assessment Exam Answers | CCNA5.NET

  • 29/03/2018 17:28
  • /
  • 66

CCNA 2 v6.0 Routing & Switching Essentials Chapter 7 SIC: VLANs, Trunking, and Router-on-a-Stick A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science LLC network with VLANs, Trunking, inter-VLAN routing, and IPv4 standard ACLs. As part of this process, you will perform basic VLAN configuration tasks, address router interfaces and hosts, and implement two ACLs. You are not required to configure the Quark switch, or any of the servers. Note: In order to keep the assessment activity as brief as possible, you will only be partially configuring some devices, as directed in the instructions. In a real network, all devices would be fully

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I Option A | CCNA5.NET

  • 29/03/2018 16:27
  • /
  • 66

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I – Option A A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network. You will perform basic router configuration tasks, address router interfaces and hosts, and configure VLANs, trunking, and routing between VLANs. You will also configure and customize RIPv2 and control access to router vty lines with a standard named ACL. For a full list of tasks, see below. You are not required to configure the following: Main-4-SW Remote-SW LAN2-1 Remote-A NetAdmin Internet Hosts attached to Main-3-SW All IOS device configurations should be completed from a direct

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I Option B | CCNA5.NET

  • 29/03/2018 15:25
  • /
  • 69

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I – Option B A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network. You will perform basic router configuration tasks, address router interfaces and hosts, and configure VLANs, trunking, and routing between VLANs. You will also configure and customize RIPv2 and control access to router vty lines with a standard named ACL. For a full list of tasks, see below. You are not required to configure the following: SW-Bldg-B-1 SW-Branch BLDG-B-1 Branch-1 Admin Web Hosts attached to SW-Bldg-A-2 All IOS device configurations should be completed from a direct

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option A | CCNA5.NET

  • 29/03/2018 14:24
  • /
  • 64

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option A A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the XYZ Corporation network You will establish network connectivity by configuring IPv4 and IPv6 addresses on router interfaces. You will configure the DHCPv4 and NAT addressing services, and establish communication between networks by configuring default and static routes in both IPv4 and IPv6. You are not required to configure: ADMIN Web SW-Bldg-A SW-Bldg-A-1 All IOS device configurations should be completed from a direct terminal connection to the device console. You will practice and be assessed on the

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option B | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option B A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network You will establish network connectivity by configuring IPv4 and IPv6 addresses on router interfaces. You will configure the DHCPv4 and NAT addressing services, and establish communication between networks by configuring default and static routes in both IPv4 and IPv6. You are not required to configure: NetAdmin Internet Main-1-SW Main-2-SW All IOS device configurations should be completed from a direct terminal connection to the device console. You will practice and be assessed on the

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I Option A | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I – Option A A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network. You will perform basic router configuration tasks, address router interfaces and hosts, and configure VLANs, trunking, and routing between VLANs. You will also configure and customize RIPv2 and control access to router vty lines with a standard named ACL. For a full list of tasks, see below. You are not required to configure the following: Main-4-SW Remote-SW LAN2-1 Remote-A NetAdmin Internet Hosts attached to Main-3-SW All IOS device configurations should be completed from a direct

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option A | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option A A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the XYZ Corporation network You will establish network connectivity by configuring IPv4 and IPv6 addresses on router interfaces. You will configure the DHCPv4 and NAT addressing services, and establish communication between networks by configuring default and static routes in both IPv4 and IPv6. You are not required to configure: ADMIN Web SW-Bldg-A SW-Bldg-A-1 All IOS device configurations should be completed from a direct terminal connection to the device console. You will practice and be assessed on the

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option B | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part II Option B A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network You will establish network connectivity by configuring IPv4 and IPv6 addresses on router interfaces. You will configure the DHCPv4 and NAT addressing services, and establish communication between networks by configuring default and static routes in both IPv4 and IPv6. You are not required to configure: NetAdmin Internet Main-1-SW Main-2-SW All IOS device configurations should be completed from a direct terminal connection to the device console. You will practice and be assessed on the

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I Option B | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Practice Skills Assessment Part I – Option B A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science Academy network. You will perform basic router configuration tasks, address router interfaces and hosts, and configure VLANs, trunking, and routing between VLANs. You will also configure and customize RIPv2 and control access to router vty lines with a standard named ACL. For a full list of tasks, see below. You are not required to configure the following: SW-Bldg-B-1 SW-Branch BLDG-B-1 Branch-1 Admin Web Hosts attached to SW-Bldg-A-2 All IOS device configurations should be completed from a direct

CCNA 2 v6.0 RSE Chapter 2 SIC Practice Skills Assessment Option A – Packet Tracer Answers | CCNA5.NET

CCNA 2 v6.0 Routing and Switching Essentials Chapter 2 SIC: Static Routing and Basic Router Configuration Type A Chapter 2 SIC Practice Skills Assessment A few things to keep in mind while completing this activity: Do not use the browser Backbutton or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessmentbutton in the browser window to submit your work. Introduction New Corp. is preparing to convert its network to use IPv6. It is experimenting with the transition, and has set up a test network that is configured with both IPv4 and IPv6 addressing on all hosts and device interfaces. The company will be using default, static, and floating static routes to create connectivity in the network. In this practice skills assessment, you will configure the New Corp. network with IPv4 and IPv6 interface and host addressing, and IPv4 and IPv6 default, static, and floating static

CCNA 2 v6.0 RSE Chapter 2 SIC Practice Skills Assessment Option B – Packet Tracer Answers | CCNA5.NET

CCNA 2 v6.0 Routing and Switching Essentials Chapter 2 SIC: Static Routing and Basic Router Configuration Type B A few things to keep in mind while completing this activity:1. Do not use the browser Back button or close or reload any exam windows during the exam.2. Do not close Packet Tracer when you are done. It will close automatically.3. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure SW-1 with an initial configuration, SSH, and port security. You are only required to configure SW-1 in this assessment. All IOS device configurations should be completed from a direct terminal connection to the device console. It is possible that information that is required to complete the configurations has not been given to you. In that case, create the values that you need to complete the requirements. These values may include certain IP addresses, passwords, interface descriptions,

CCNA 2 v6.0 Chapter 7 RSE Practice Skills Assessment Exam Answers | CCNA5.NET

CCNA 2 v6.0 Routing & Switching Essentials Chapter 7 SIC: VLANs, Trunking, and Router-on-a-Stick A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when you are done. It will close automatically. Click the Submit Assessment button in the browser window to submit your work. Introduction In this practice skills assessment, you will configure the Science LLC network with VLANs, Trunking, inter-VLAN routing, and IPv4 standard ACLs. As part of this process, you will perform basic VLAN configuration tasks, address router interfaces and hosts, and implement two ACLs. You are not required to configure the Quark switch, or any of the servers. Note: In order to keep the assessment activity as brief as possible, you will only be partially configuring some devices, as directed in the instructions. In a real network, all devices would be fully

CCNA2 v6.0 Chapter 5 Exam Answers 2017

1. Which statement describes the port speed LED on the Cisco Catalyst 2960 switch? If the LED is green, the port is operating at 100 Mb/s.* If the LED is off, the port is not operating. If the LED is blinking green, the port is operating at 10 Mb/s. If the LED is amber, the port is operating at 1000 Mb/s. 2. Which command is used to set the BOOT environment variable that defines where to find the IOS image file on a switch? config-register boot system* boot loader confreg 3. What is a function of the switch boot loader? to speed up the boot process to provide security for the vulnerable state when the switch is booting to control how much RAM is available to the switch during the boot process to provide an environment to operate in when the switch operating system cannot be found* 4. Which interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch? VLAN 1* Fa0/0 Fa0/1 interface connected to the default gateway VLAN 99

CCNA2 v6.0 Chapter 6 Exam Answers 2017

1. What are three primary benefits of using VLANs? (Choose three.) security* a reduction in the number of trunk links cost reduction* end user satisfaction improved IT staff efficiency* no required configuration 2. Which type of VLAN is used to designate which traffic is untagged when crossing a trunk port? data default native* management 3. A network administrator is determining the best placement of VLAN trunk links. Which two types of point-to-point connections utilize VLAN trunking?​ (Choose two.) between two switches that utilize multiple VLANs* between a switch and a client PC between a switch and a server that has an 802.1Q NIC* between a switch and a network printer between two switches that share a common VLAN 4. What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3? Enter the no vlan 2 and the vlan 3 commands in global configuration mode. Enter the switchport access vlan 3 command in interface

CCNA2 v6.0 Chapter 7 Exam Answers 2017

1. In which configuration would an outbound ACL placement be preferred over an inbound ACL placement? when the ACL is applied to an outbound interface to filter packets coming from multiple inbound interfaces before the packets exit the interface* when a router has more than one ACL when an outbound ACL is closer to the source of the traffic flow when an interface is filtered by an outbound ACL and the network attached to the interface is the source network being filtered within the ACL 2. Which address is required in the command syntax of a standard ACL? source MAC address destination MAC address source IP address* destination IP address 3. Which statement describes a difference between the operation of inbound and outbound ACLs? In contrast to outbound ALCs, inbound ACLs can be used to filter packets with multiple criteria. Inbound ACLs can be used in both routers and switches but outbound ACLs can be used only on routers. Inbound ACLs are processed before the


About Us

CCNA v5 Answers, CCNA v5 Blog, CCNA 5 Blog, CCNA Blog

Articles

Our Contacts