8.2.4.12 Packet Tracer – Troubleshooting Enterprise Networks 1

  • 07/07/2018 17:37
  • 105

8.2.4.12 Packet Tracer – Troubleshooting Enterprise Networks 1

Packet Tracer – Troubleshooting Enterprise Networks 1 (Answer Version)

Answer Note: Red font color or Gray highlights indicate text that appears in the Answer copy only.

Topology

8.2.4.12 Packet Tracer – Troubleshooting Enterprise Networks 1

8.2.4.12 Packet Tracer – Troubleshooting Enterprise Networks 1

Addressing Table

Device Interface IP Address Subnet Mask Default Gateway
R1 S0/0/0 10.1.1.1 255.255.255.252 N/A
S0/0/1 10.3.3.1 255.255.255.252 N/A
R2 G0/0 192.168.40.1 255.255.255.0 N/A
G0/1 DHCP assigned DHCP assigned N/A
S0/0/0 10.1.1.2 255.255.255.252 N/A
S0/0/1 10.2.2.1 255.255.255.252 N/A
R3 G0/0.10 192.168.10.1 255.255.255.0 N/A
G0/0.20 192.168.20.1 255.255.255.0 N/A
G0/0.30 192.168.30.1 255.255.255.0 N/A
G0/0.88 192.168.88.1 255.255.255.0 N/A
S0/0/0 10.3.3.2 255.255.255.252 N/A
S0/0/1 10.2.2.2 255.255.255.252 N/A
S1 VLAN 88 192.168.88.2 255.255.255.0 192.168.88.1
S2 VLAN 88 192.168.88.3 255.255.255.0 192.168.88.1
S3 VLAN 88 192.168.88.4 255.255.255.0 192.168.88.1
PC1 NIC DHCP assigned DHCP assigned DHCP assigned
PC2 NIC DHCP assigned DHCP assigned DHCP assigned
PC3 NIC DHCP assigned DHCP assigned DHCP assigned
TFTP Server NIC 192.168.40.254 255.255.255.0 192.168.40.1

Background

This activity uses a variety of technologies you have encountered during your CCNA studies, including VLANs, STP, routing, inter-VLAN routing, DHCP, NAT, PPP, and Frame Relay. Your task is to review the requirements, isolate and resolve any issues, and then document the steps you took to verify the requirements.

Requirements

VLANs and Access

  • S2 is the spanning-tree root for VLAN 1, 10, and 20. S3 is the spanning-tree root for VLAN 30 and 88.
  • The trunk links connecting the switches are in native VLAN 99.
  • R3 is responsible for inter-VLAN routing and serves as the DHCP server for VLANs 10, 20, and 30.

Routing

  • Each router is configured with EIGRP and uses AS 22.
  • R2 is configured with a default route pointing to the ISP and redistributes the default route.
  • NAT is configured on R2 and no untranslated addresses are permitted to cross the Internet.

WAN Technologies

  • The serial link between R1 and R2 uses Frame Relay.
  • The serial link between R2 and R3 uses HDLC encapsulation.
  • The serial link between R1 and R3 uses PPP with CHAP.

Connectivity

  • Devices should be configured according to the Addressing Table.
  • Every device should be able to ping every other device.

Troubleshooting Documentation

Device Problem Solution
R1 R1 and R2 are not forming an adjacency interface Serial0/0/0

encapsulation frame-relay

R1 Username and passwords are incorrect username R3 password 0 ciscoccna
R2 TFTP Server cannot ping the Outside Host interface g0/0

no ip nat outside

ip nat inside

interface g0/1

ip nat outside

R2 Default route is pointing to the incorrect interface no ip route 0.0.0.0 0.0.0.0 g0/0

ip route 0.0.0.0 0.0.0.0 g0/1

S1 Native VLAN mismatch interface range fa0/1-4

switchport trunk native vlan 99

S2 This switch is not the root bridge for VLANs 1, 10, and 20 spanning-tree vlan 1,10,20 root primary
S3 The PCs do not pull a DHCP address interface g0/1

switchport mode trunk

Verification Documentation

Capture output from verification commands and provide documentation proving that each of the requirements has been satisfied.

Answer’s Note: The answer key for this section is left blank because there are many ways to verify the requirements.

Suggested Scoring Rubric

Packet Tracer scores 60 points. The troubleshooting documentation and Answer verification is worth 40 points.


Bình luận

About Us

CCNA v5 Answers, CCNA v5 Blog, CCNA 5 Blog, CCNA Blog

Articles

Our Contacts